loctite products

Providing you the best range of loctite ea 3478 superior metal adhesive with effective & timely delivery.

Loctite EA 3478 Superior Metal Adhesive

Request Callback

₹ 8000 / Piece Get Latest Price

Product Brochure
BrandLoctite
Model NumberEA 3478
TechnologyEpoxy
Packaging Size110g+890g
Packaging TypeBox
FormPaste
Chemical ResistanceWater
IDH No.680035
Abrasion ResistanceYes
Known AsLocatite , Fixmaster , Superior Metal
Box Contains2pcs

Minimum order quantity: 20 Piece

Product details:
  • 2-part, ferro-silicon filled epoxy resin system. Extremely resistant to corrosion, chemical attack and abrasion.LOCTITE EA 3478 is a 2-part, ferro-silicon filled epoxy resin system. It is extremely resistant to corrosion, chemical attack and abrasion. It is ideal for restoring parts worn by mechanical and/or corrosion impact. Helps to restore tolerances to worn shafts, repairing worn keyways and damaged housings, filling pitted surfaces in worn machinery and restoring fit to bearing housings.
  • Rebuilds keyways and spline assemblies
  • Rebuilds bearings, clamp connections, tensioning elements, gear wheels or bearing seats
  • Ferro-silicon filled with outstanding compression strength
  • Ideal for renewing surfaces subjected to compression, thrust, impact and harsh environments
GENERAL INFORMATION
  • This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). 
Surface Preparation
  • Proper surface preparation is critical to the long-term performance of this product. The exact requirements vary with severity of the application, expected service life, and initial substrate conditions
Directions for use:
  • Remove dirt, oil, grease, etc. with a suitable cleaner, e.g. high pressure water cleaning system using Loctite SF 7840 (Loctite Natural Blue cleaner/degreaser).
  • Blast all surfaces to be coated with a sharp edged angular grit to a depth of profile of 75 to 100 microns and a degree of cleanliness of Near White Metal (SIS SA 2½ /SSPC-SP 10).
  • After blasting, metal surfaces should be cleaned with waterless cleaner, e.g. with Loctite SF 7611 (Loctite Pro Strength Parts Cleaner), and be coated before any oxidation or contamination takes place.
  • Metal that has been in contact with salt solutions, e.g. seawater, should be grit blasted, high-pressure water blasted, and left for 24 hours to allow any salts in the metal to sweat to the surface. A test for chloride contamination should be performed. The procedure should be repeated until chloride concentration on the surface is below 40 ppm.
  • Mix 4 part resin to 1 part hardener by volume (7.25 to 1 by weight) or transfer entire kit onto a clean and dry mixing surface and mix thoroughly until color is consistent.
  • Apply fully mixed material to prepared surface.
If using to rebuild shaft, the following applies:
  • Machine the worn area down 3mm (0.125 in) to produce a square shoulder on part. The material is stronger with a square edge versus a feathered edge.
  • Machine a spiral cut in bottom of area to be repaired to provide mechanical keying into surface.
  • Apply excess product to ensure small shrinkage during cure does not produce depression.
  • Machine the surface to original dimensions prior to full cure, as the product is very wear resistant.
Inspection
  • Visually inspect for pinholes and misses just after application.
  • Once the coating has cured, repeat visual inspection to confirm it is free from pinholes, misses and mechanical damages.
  • Control thickness of the coating, especially in the critical points.
  • Perform a test with a holiday detector to confirm coating continuity.
Coverage
  • To achieve a 6 mm (.25 in) thickness, the coverage rate will be 323 cm² (36 in²) for .45 kg (1 lb), excluding overthickness, repairs, etc.
X

Contact Us

Yousuf Ismail (Proprietor)
Mufaddal Enterprises
New 109/013/ Old 109/006, Yusufi Manzil, Model House
Lucknow - 226001, Uttar Pradesh, India

Get Directions
Send Email
Share: